Araldite® 2010-1 200ml
Pasty Two-Component Adhesive Based on Epoxy Resin
- Fast curing
- Tough and elastic
- Low shrinkage
- High tensile shear and peel strength
- For bonding a wide variety of commonly used materials
Araldite® 2010-1 is a fast-curing, pasty, general-purpose two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics, and most commonly used materials.
| 2K Epoxy (Fast Curing) | |
|---|---|
| Viscosity | approx. 80 Pa.s |
| Processing Time (23°C): | 10 minutes |
| Handling Strength (23°C): | 30 minutes (1 MPa) |
| 50% Strength (23°C) | 3 hours |
| 50% Strength (60°C) | 20 minutes |
| Tensile Shear Strength (23°C) on GRP: | 5 MPa |
| Tensile Shear Strength (23°C) on Aluminum: | 23 MPa |
| Peel Strength (23°C) on Aluminum: | 6 N/mm² |
| Typical Tg (Softening Temperature) | 40 °C |
| Maximum Temperature Leading to TSS of 5 MPa | 80 °C |
- Container: 200 ml dual cartridge with static mixing nozzle
- Article number: ARA-2010-200
- Net weight: 0.2 kg
Product safety information (status 06/2019 & 09/2019)
- Signal word: Danger and Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H411 Toxic to aquatic life with long lasting effects.
- H413 May cause long lasting harmful effects to aquatic life.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust, smoke, gas, mist, vapors, or aerosols.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves, protective clothing, eye protection, face protection.
- P303 + P361 + P353 IF ON SKIN or hair: Remove immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a poison center or doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call a poison center or doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice or attention.
- P391 Collect spillage.
Araldite® 2011 50ml
Paste-like two-component adhesive based on epoxy resin
- All-purpose adhesive
- Low shrinkage
- Long service life
- Good resistance to dynamic loads
- For bonding a wide variety of the most commonly used materials
Araldite® 2011 is a paste-like, all-purpose two-component adhesive that cures at room temperature.
The paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials. It is a versatile adhesive suitable for both craftsmen and most industrial applications.
Product safety information (status 06/2019 & 09/2019)
- Signal word: Danger + Warning
GHS Safety Statements / H Statements
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
- P303 + P361 + P353 IF ON SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water.
- P304 + P340 + P310 IF INHALED: Move person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2011 200ml
Paste-like two-component adhesive based on epoxy resin
- All-purpose adhesive
- Low shrinkage
- Long service life
- Good resistance to dynamic loads
- For bonding a wide variety of the most commonly used materials
Araldite® 2011 is a paste-like, all-purpose two-component adhesive that cures at room temperature.
The paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials. It is a versatile adhesive suitable for both craftsmen and most industrial applications.
Product safety information (status: 01/2018 & 06/2018)
- Signal word: Danger + Warning
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | transparent – yellow |
| Viscosity see also -> viscosity table | 40 Pa.s |
| Processing time for 100g at 23°C | 100 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 420 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 1900 N/mm² |
| Elongation at break at 23°C | 9 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 5 N/mm² |
| Glass transition temperature curing 16 h/40°C | 45 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 90 °C |
Safety instructions
GHS / H Statements
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
- P303 + P361 + P353 IF ON SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water.
- P304 + P340 + P310 IF INHALED: Move person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2011 300ml
Paste-like two-component adhesive based on epoxy resin
- All-purpose adhesive
- Low shrinkage
- Long service life
- Good resistance to dynamic loads
- For bonding a wide variety of the most commonly used materials
Araldite® 2011 is a paste-like, all-purpose two-component adhesive that cures at room temperature.
The paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials. It is a versatile adhesive suitable for both craftsmen and most industrial applications.
Product safety information (status: 01/2018 & 06/2018)
- Signal word: Danger + Warning
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | transparent – yellow |
| Viscosity see also -> viscosity table | 40 Pa.s |
| Processing time for 100g at 23°C | 100 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 420 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 1900 N/mm² |
| Elongation at break at 23°C | 9 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 5 N/mm² |
| Glass transition temperature curing 16 h/40°C | 45 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 90 °C |
Safety instructions
GHS / H Statements
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
- P303 + P361 + P353 IF ON SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water.
- P304 + P340 + P310 IF INHALED: Move person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2011 2kg work pack
Paste-like two-component adhesive based on epoxy resin
- All-purpose adhesive
- Low shrinkage
- Long service life
- Good resistance to dynamic loads
- For bonding a wide variety of the most commonly used materials
Araldite® 2011 is a paste-like, all-purpose two-component adhesive that cures at room temperature.
The paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials. It is a versatile adhesive suitable for both craftsmen and most industrial applications.
- Packaging: 2kg work pack (tin with 2 mixing sticks)
- Article number: ARA-2011-2KG
Product safety information
(status: 01/2018 & 06/2018)
- Signal word: Danger + Warning
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | transparent – yellow |
| Viscosity | 40 Pa.s |
| Processing time for 100g at 23°C | 100 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 420 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 1900 N/mm² |
| Elongation at break at 23°C | 9 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 5 N/mm² |
| Glass transition temperature curing 16 h/40°C | 45 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 90 °C |
Safety instructions
GHS / H Statements
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
- P303 + P361 + P353 IF ON SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water.
- P304 + P340 + P310 IF INHALED: Move person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2012 50ml
Paste-like two-component adhesive based on epoxy resin
- Fast curing
- All-purpose adhesive
- Low shrinkage
- For bonding a wide variety of materials
- Tough and elastic Araldite® 2012 is a fast-curing, high-viscosity all-purpose two-component adhesive at room temperature.
The thixotropic paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials.
It is a versatile adhesive suitable for both craftsmen and most industrial applications.
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | amber– yellow |
| Viscosity | 30 Pa.s |
| Processing time for 100g at 23°C | 6 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 20 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 18 N/mm² |
| Modulus of elasticity at 23°C | 2520 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 5,5 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 70 °C |
- Packaging: 50ml double cartridge with forced mixing nozzle
- Article number: ARA-2012-50
- Net weight: 0,05kg
Product safety information (status01/2020)
- Signal word: Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P337 + P313 If eye irritation persists: Get medical advice / attention.
- P362 + P364 Remove contaminated clothing and wash before reuse.
- P391 Collect spillage.
Safety instructions GHS / EUH Statements
- EUH205 Contains epoxy-containing compounds. May cause allergic reactions.
Araldite® 2012 200ml
Paste-like two-component adhesive based on epoxy resin
- Fast curing
- All-purpose adhesive
- Low shrinkage
- For bonding a wide variety of materials
- Tough and elastic Araldite® 2012 is a fast-curing, high-viscosity all-purpose two-component adhesive at room temperature.
The thixotropic paste is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials.
It is a versatile adhesive suitable for both craftsmen and most industrial applications.
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | amber- yellow |
| Viscosity | 30 Pa.s |
| Processing time for 100g at 23°C | 6 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 20 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 18 N/mm² |
| Modulus of elasticity at 23°C | 2520 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 5,5 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 70 °C |
- Packaging: 200ml double cartridge with forced mixing nozzle
- Article number: ARA-2012-200
- Net weight: 0,2kg
Product safety information (status01/2020)
- Signal word: Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P337 + P313 If eye irritation persists: Get medical advice / attention.
- P362 + P364 Remove contaminated clothing and wash before reuse.
- P391 Collect spillage.
Safety instructions GHS / EUH Statements
- EUH205 Contains epoxy-containing compounds. May cause allergic reactions.
Araldite® 2013-1 50ml
Paste-like two-component adhesive based on epoxy resin
- Metallic appearance
- Thixotropic
- Good resistance to environmental influences and chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
- For bonding a wide variety of materials
Araldite® 2013-1 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and strength and has excellent resistance to environmental influences and chemicals.
Although Araldite® 2013-1 is designed as a metal adhesive, it is also suitable for other materials such as ceramics, glass, rubber, rigid plastics and most commonly used materials.
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 65 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 2530 N/mm² |
| Elongation at break at 23°C | 1% |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 75 °C |
- Packaging: 50ml double cartridge with forced mixing nozzle
- Article number: ARA-2013-50
- Net weight: 0,05kg
Product safety information (status01/2020)
- Signal word: Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2013-1 200ml
Paste-like two-component adhesive based on epoxy resin
- Metallic appearance
- Thixotropic
- Good resistance to environmental influences and chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
- For bonding a wide variety of materials
Araldite® 2013-1 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and strength and has excellent resistance to environmental influences and chemicals.
Although Araldite® 2013-1 is designed as a metal adhesive, it is also suitable for other materials such as ceramics, glass, rubber, rigid plastics and most commonly used materials.
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 65 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 2530 N/mm² |
| Elongation at break at 23°C | 1 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 75 °C |
- Packaging: 200ml double cartridge with forced mixing nozzle
- Article number: ARA-2013-200
- Net weight: 0,2kg
Product safety information
(status06/2018 & 04/2019)
- Signal word: Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2013 2kg work pack
Paste-like two-component adhesive based on epoxy resin
- Metallic appearance
- Thixotropic
- Good resistance to environmental influences and chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
- For bonding a wide variety of materials
Araldite® 2013 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and strength and has excellent resistance to environmental influences and chemicals.
Although Araldite® 2013 is designed as a metal adhesive, it is also suitable for other materials such as ceramics, glass, rubber, rigid plastics and most commonly used materials.
- Packaging: 2kg work pack (2 tins with 2 mixing sticks)
Product safety information (status06/2018 & 04/2019)
- Signal word: Warning
| 2K EP epoxy resin adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 65 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 26 N/mm² |
| Modulus of elasticity at 23°C | 2530 N/mm² |
| Elongation at break at 23°C | 1 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 75 °C |
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2014-2 50ml
Paste-like two-component adhesive based on epoxy resin
- Gray paste
- High heat resistance and resistance to chemicals
- Low shrinkage
- Excellent resistance to water and a wide range of chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
Araldite® 2014-2 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and toughness and has excellent resistance to environmental influences and chemicals.
The adhesive is used for bonding metal, electronic components, GFRP components and a wide variety of other parts in applications where higher temperature values than normal or more demanding environmental conditions occur during use. Due to its low outgassing, this product is suitable for applications in the fields of professional electronic communication and aerospace.
| 2K EP epoxy resin adhesive with a mixing ratio of 2:1 | |
|---|---|
| Color (mixed) | dark gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 60 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 180 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 19 N/mm² |
| Modulus of elasticity at 23°C | 4000 N/mm² |
| Elongation at break at 23°C | 1 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 3 N/mm² |
| Glass transition temperature curing 16 h/40°C | 85 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 140 °C |
- Packaging: 50ml double cartridge with forced mixing nozzle
Product safety information
(status 07/2018 & 11/2018)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H373 May cause damage to organs through prolonged or repeated exposure by swallowing.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Araldite® 2014-2 200ml
Paste-like two-component adhesive based on epoxy resin
- Gray paste
- High heat resistance and resistance to chemicals
- Low shrinkage
- Excellent resistance to water and a wide range of chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
Araldite® 2014-2 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and toughness and has excellent resistance to environmental influences and chemicals.
The adhesive is used for bonding metal, electronic components, GFRP components and a wide variety of other parts in applications where higher temperature values than normal or more demanding environmental conditions occur during use. Due to its low outgassing, this product is suitable for applications in the fields of professional electronic communication and aerospace.
| 2K EP epoxy resin adhesive with a mixing ratio of 2:1 | |
|---|---|
| Color (mixed) | dark gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 60 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 180 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 19 N/mm² |
| Modulus of elasticity at 23°C | 4000 N/mm² |
| Elongation at break at 23°C | 1 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 3 N/mm² |
| Glass transition temperature curing 16 h/40°C | 85 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 140 °C |
- Packaging: 200ml double cartridge with forced mixing nozzle
- Net weight: 0.2kg
Product safety information
(status 07/2018 & 11/2018)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H373 May cause damage to organs through prolonged or repeated exposure by swallowing.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Araldite® 2014-2 2kg Work pack
Paste-like two-component adhesive based on epoxy resin
- Gray paste
- High heat resistance and resistance to chemicals
- Low shrinkage
- Excellent resistance to water and a wide range of chemicals
- Gap-filling, does not run at application thicknesses up to 5 mm
Araldite® 2014-2 is a paste-like two-component adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and toughness and has excellent resistance to environmental influences and chemicals.
The adhesive is used for bonding metal, electronic components, GFRP components and a wide variety of other parts in applications where higher temperature values than normal or more demanding environmental conditions occur during use. Due to its low outgassing, this product is suitable for applications in the fields of professional electronic communication and aerospace.
- Packaging: 2kg work pack (2 tins with 2 mixing sticks)
Product safety information (status 07/2018 & 11/2018)
- Signal word: Danger
| 2K EP epoxy resin adhesive with a mixing ratio of 2:1 | |
|---|---|
| Color (mixed) | dark gray |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 60 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 180 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 19 N/mm² |
| Modulus of elasticity at 23°C | 4000 N/mm² |
| Elongation at break at 23°C | 1 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 3 N/mm² |
| Glass transition temperature curing 16 h/40°C | 85 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 140 °C |
GHS Safety Statements / H Statements
- H302 Harmful if swallowed
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H373 May cause damage to organs through prolonged or repeated exposure by swallowing.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Araldite® 2015-1 50ml
Paste-like two-component adhesive based on epoxy resin
- Thixotropic
- Toughened adhesive
- Gap-filling, does not run at application thicknesses up to 10 mm
- Suitable for SMC and GFRP bonding
- High tensile shear and peel strength
Araldite® 2015-1 is a paste-like two-component adhesive that cures at room temperature and forms an elastic bond.
The thixotropic paste does not run at application thicknesses up to 10 mm and is particularly suitable for SMC and GFRP bonding.
| 2K EP epoxy resin adhesive (toughened) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | beige |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 35 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 16 N/mm² |
| Modulus of elasticity at 23°C | 2000 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Glass transition temperature curing 16 h/40°C | 67 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 110 °C |
- Packaging: 50ml double cartridge with static mixer nozzle
- Net weight: 0.05kg
Product safety information
(status 08/2018)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Important: This product currently contains Bisphenol A (EC No. 201-245-8), which is registered as a substance under REACH (European chemicals regulation). This means that, by law, this product may currently not be supplied to private end consumers. Only commercial customers or customers with the appropriate qualification to process this adhesive are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will take place, otherwise we would be liable to prosecution. Your order will then be cancelled and any amounts already paid will be refunded.
Thank you for your understanding!
Araldite® 2015-1 200ml
Paste-like two-component adhesive based on epoxy resin
- Thixotropic
- Toughened adhesive
- Gap-filling, does not run at application thicknesses up to 10 mm
- Suitable for SMC and GFRP bonding
- High tensile shear and peel strength
Araldite® 2015-1 is a paste-like two-component adhesive that cures at room temperature and forms an elastic bond. The thixotropic paste does not run at application thicknesses up to 10 mm and is particularly suitable for SMC and GFRP bonding.
| 2K EP epoxy resin adhesive (toughened) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | beige |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 35 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 16 N/mm² |
| Modulus of elasticity at 23°C | 2000 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Glass transition temperature curing 16 h/40°C | 67 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 110 °C |
- Packaging: 200ml double cartridge with static mixer nozzle
- Net weight: 0.2kg
Product safety information
(status 08/2018)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Important: This product currently contains Bisphenol A (EC No. 201-245-8), which is registered as a substance under REACH (European chemicals regulation). This means that, by law, this product may currently not be supplied to private end consumers. Only commercial customers or customers with the appropriate qualification to process this adhesive are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will take place, otherwise we would be liable to prosecution. Your order will then be cancelled and any amounts already paid will be refunded.
Thank you for your understanding!
Araldite® 2015-1 380ml
Paste-like two-component adhesive based on epoxy resin
- Thixotropic
- Toughened adhesive
- Gap-filling, does not run at application thicknesses up to 10 mm
- Suitable for SMC and GFRP bonding
- High tensile shear and peel strength
Araldite® 2015-1 is a paste-like two-component adhesive that cures at room temperature and forms an elastic bond. The thixotropic paste does not run at application thicknesses up to 10 mm and is particularly suitable for SMC and GFRP bonding.
| 2K EP epoxy resin adhesive (toughened) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | beige |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 35 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 16 N/mm² |
| Modulus of elasticity at 23°C | 2000 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Glass transition temperature curing 16 h/40°C | 67 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 110 °C |
- Packaging: 380ml double cartridge with static mixer nozzle
- Net weight: 0.2kg
Product safety information
(status 08/2018)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Important: This product currently contains Bisphenol A (EC No. 201-245-8), which is registered as a substance under REACH (European chemicals regulation). This means that, by law, this product may currently not be supplied to private end consumers. Only commercial customers or customers with the appropriate qualification to process this adhesive are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will take place, otherwise we would be liable to prosecution. Your order will then be cancelled and any amounts already paid will be refunded.
Thank you for your understanding!
Araldite® 2015 2kg Work Pack
Paste-like two-component adhesive based on epoxy resin
- Thixotropic
- Toughened adhesive
- Gap-filling, does not run at application thicknesses up to 10 mm
- Suitable for SMC and GFRP bonding
- High tensile shear and peel strength
Araldite® 2015 is a paste-like two-component adhesive that cures at room temperature and forms an elastic bond.
The thixotropic paste does not run at application thicknesses up to 10 mm and is particularly suitable for SMC and GFRP bonding.
- Packaging: 2kg work pack (2 tins with 2 mixing sticks)
Product safety information (status 08/2018)
- Signal word: Danger
| 2K EP epoxy resin adhesive (toughened) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | beige |
| Viscosity | thixotropic (paste-like) |
| Processing time for 100g at 23°C | 35 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 16 N/mm² |
| Modulus of elasticity at 23°C | 2000 N/mm² |
| Elongation at break at 23°C | 4 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Glass transition temperature curing 16 h/40°C | 67 °C |
| Maximum temperature that results in a ZSF of 5 N/mm² | 110 °C |
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after use.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call POISON CENTER / doctor.
- P391 Collect spillage.
Important: This product currently contains Bisphenol A (EC No. 201-245-8), which is registered as a substance under REACH (European chemicals regulation). This means that, by law, this product may currently not be supplied to private end consumers. Only commercial customers or customers with the appropriate qualification to process this adhesive are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will take place, otherwise we would be liable to prosecution. Your order will then be cancelled and any amounts already paid will be refunded.
Thank you for your understanding!
Araldite® 2018 200ml
Flexible two-component PU adhesive system
- Good UV stability
- Ideal for bonding thermoplastics
- Low shrinkage
- Flexible
- Cures at room temperature
Araldite® 2018 is a pale, slightly thixotropic, liquid two-component polyurethane adhesive that cures at room temperature and is designed for bonding thermoplastics.
| 2K PUR polyurethane adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | colorless |
| Viscosity | 8 Pa.s |
| Processing time for 100g at 23°C | 40 minutes |
| Handling strength at 23°C for ZSF 1 N/mm² | 240 minutes |
| Tensile shear strength (ZSF) on aluminum at 23°C | 7 N/mm² |
| Modulus of elasticity at 23°C | 60 N/mm² |
| Elongation at break at 23°C | 45 % |
| Roll peel test (ISO 4587) curing 16 h/40°C | 4 N/mm² |
| Maximum temperature that results in a ZSF of 5 N/mm² | 40 °C |
- Packaging: 200ml dual cartridge with static mixing nozzle
- Net weight: 0.2 kg
Product safety information
(status 03/2018)
- Signal word: Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H314 Causes severe skin burns and serious eye damage.
- H317 May cause an allergic skin reaction.
- H330 Fatal if inhaled.
- H332 Harmful if inhaled.
- H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
- H335 May cause respiratory irritation.
- H361 Suspected of damaging fertility or the unborn child.
- H372 Causes damage to organs through prolonged or repeated exposure if swallowed.
- H411 Toxic to aquatic life with long lasting effects.
- H413 May cause long lasting harmful effects to aquatic life.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P273 Avoid release to the environment.
- P280 Wear protective gloves.
- P304 + P340 + P312 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER / doctor if you feel unwell.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P362 + P364 Take off contaminated clothing and wash it before reuse.
- P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
- P501 Dispose of contents / container at an approved waste disposal facility in accordance with local / regional / national / international regulations.
Araldite® 2020 0.5kg working pack
Colorless two-component epoxy adhesive system
- Low-viscosity, crystal-clear adhesive
- Especially suitable for glass and ceramic materials
- Suitable for colorless cast parts and laminates
- Refractive index closely matches that of glass
Araldite® 2020 is a low-viscosity, two-component adhesive that cures at room temperature and was specifically designed for bonding glass.
The system is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials, and can also be applied easily over large areas.
- Packaging: 0.5kg working pack (2 tins with pipettes, cup and mixing sticks)
Product safety information (status 08/2018)
- Signal word: Danger
| 2K epoxy resin Colorless | |
|---|---|
| Viscosity | 150 mPa.s |
| Processing time (23°C): | 40–50 minutes |
| Handling strength (23°C): | 16 hours (1 MPa) |
| Cure time (23°C): | 23 hours (10 MPa) |
| Tensile shear strength (23°C) on glass: | 25 N/mm² |
| Tensile shear strength (23°C) on aluminum: | 16 N/mm² |
| Glass transition temperature: | 39.5 °C |
| Modulus of elasticity (E-modulus): | 2467.9 MPa |
| Flexural strength: | 74.9 MPa |
| Refractive index: | 1.553 |
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H332 Harmful if inhaled.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P391 Collect spillage.
Araldite® 2021-1 50ml
Toughened two-component adhesive based on methacrylic acid ester
- Excellent adhesion to a wide range of plastics, composites and metals
- High tensile shear and peel strength
- Very good resistance to chemicals and water
- Very fast cure with good gap-filling properties
- Usable at temperatures up to 100°C
Note: Araldite® 2021-1 is not suitable for bonding copper, brass or copper alloys.
Araldite® 2021-1 is a general-purpose, two-component methacrylate adhesive that cures at room temperature and is designed for fast bonding of a wide variety of substrates.
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information (status 09/2015)
- Signal word: Danger
| 2K MMA methacrylate adhesive (tough-elastic) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | light yellow |
| Viscosity | thixotropic (paste-like) |
| Working time for 100g at 23°C | 3 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 8 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 23 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 2300 N/mm² |
| Elongation at break at 23°C | 10 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 11 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 110 °C |
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H242 Heating may cause a fire.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H373 May cause damage to organs through prolonged or repeated exposure.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233 Keep container tightly closed.
- P235 Keep cool.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water / shower.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2021-1 380ml
Toughened two-component adhesive based on methacrylic acid ester
- Excellent adhesion to a wide range of plastics, composites and metals
- High tensile shear and peel strength
- Very good resistance to chemicals and water
- Very fast cure with good gap-filling properties
- Usable at temperatures up to 100°C
Note: Araldite® 2021-1 is not suitable for bonding copper, brass or copper alloys.
Araldite® 2021-1 is a general-purpose, two-component methacrylate adhesive that cures at room temperature and is designed for fast bonding of a wide variety of substrates.
| 2K MMA methacrylate adhesive (tough-elastic) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | light yellow |
| Viscosity | thixotropic (paste-like) |
| Working time for 100g at 23°C | 3 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 8 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 23 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 2300 N/mm² |
| Elongation at break at 23°C | 10 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 11 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 110 °C |
- Packaging: 380ml dual cartridge with static mixing nozzle
- Net weight: 0.38kg
Product safety information
(status 09/2015)
- Signal word: Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H242 Heating may cause a fire.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H373 May cause damage to organs through prolonged or repeated exposure.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233 Keep container tightly closed.
- P235 Keep cool.
- P280 Wear protective gloves / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water / shower.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2022-1 50ml
Toughened two-component adhesive based on methacrylic acid ester
- Excellent adhesion to a wide range of plastics, composites and metals
- Excellent resistance to gasoline and oil
- Tolerant of “less-than-ideal” surface preparation
- Fast curing
- Gap filling up to 4 mm
Araldite® 2022-1 is a two-component methacrylate adhesive that cures at room temperature and is designed for fast bonding of a wide variety of substrates, including “difficult-to-bond” materials.
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information (status 07/2017)
- Signal word: Danger
| 2K MMA methacrylate adhesive (tough-elastic) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | cream white |
| Viscosity | thixotropic (paste-like) |
| Working time for 100g at 23°C | 10 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 18 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 25 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 2050 N/mm² |
| Elongation at break at 23°C | 3 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 4 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 100 °C |
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H242 Heating may cause a fire.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H373 May cause damage to organs through prolonged or repeated exposure.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233 Keep container tightly closed.
- P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P235 Keep cool.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2022-1 380ml
Toughened two-component adhesive based on methacrylic acid ester
- Excellent adhesion to a wide range of plastics, composites and metals
- Excellent resistance to gasoline and oil
- Tolerant of “less-than-ideal” surface preparation
- Fast curing
- Gap filling up to 4 mm
Araldite® 2022-1 is a two-component methacrylate adhesive that cures at room temperature and is designed for fast bonding of a wide variety of substrates, including “difficult-to-bond” materials.
| 2K MMA methacrylate adhesive (tough-elastic) with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | cream white |
| Viscosity | thixotropic (paste-like) |
| Working time for 100g at 23°C | 10 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 18 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 25 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 2050 N/mm² |
| Elongation at break at 23°C | 3 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 4 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 100 °C |
- Packaging: 380ml dual cartridge with static mixing nozzle
- Net weight: 0.38kg
Product safety information
(status 07/2017)
- Signal word: Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H242 Heating may cause a fire.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and serious eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H373 May cause damage to organs through prolonged or repeated exposure.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233 Keep container tightly closed.
- P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P235 Keep cool.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2028-1 50ml
Transparent two-component polyurethane adhesive
- Transparent – crystal clear
- Fast curing
- Good UV stability
- Suitable for bonding metals and plastics
Araldite® 2028-1 is a clear, transparent two-component polyurethane adhesive that cures at room temperature.
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information (status 10/2018)
- Signal word: Warning
| 2K PUR polyurethane adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | clear, transparent |
| Viscosity | 5 Pa·s |
| Working time for 100g at 23°C | 6 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 15 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 14 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 10 N/mm² |
| Elongation at break at 23°C | 34 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 1.2 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 55 °C |
GHS Safety Statements / H Statements
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H412 Harmful to aquatic life with long lasting effects.
Additional labeling
- EUH204 Contains isocyanates. May produce an allergic reaction.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapours.
- P264 Wash skin thoroughly after handling.
- P272 Contaminated work clothing should not be allowed out of the workplace.
- P280 Wear eye protection, face protection and protective gloves.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
- P337 + P313 If eye irritation persists: Get medical advice/attention.
- P362 + P364 Take off contaminated clothing and wash it before reuse.
- P501 Dispose of contents/container at an approved waste disposal facility in accordance with local/regional/national/international regulations.
Araldite® 2029-1 50ml
Gap-filling two-component polyurethane adhesive
- Gap-filling
- Long open time
- High strength for metal bonding
- Good adhesion to copper and brass
Araldite® 2029-1 is a grey, paste-like two-component polyurethane adhesive that cures at room temperature. Araldite® 2029-1 is a high-strength adhesive that is well suited for structural bonding applications. High strength on metals.
- Packaging: 50ml dual cartridge with static mixing nozzle
- Article number: ARA-2029-50
- Net weight: 0.05kg
Product safety information (status 10/2018)
- Signal word: Warning + Danger
| 2K PUR polyurethane adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | grey |
| Viscosity | thixotropic (paste-like) |
| Working time for 100g at 23°C | 40 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 240 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 25 N/mm² |
| Modulus of elasticity (E-modulus) at 23°C | 580 N/mm² |
| Elongation at break at 23°C | 47 % |
| Floating roller peel test (ISO 4587) cure 16 h/40°C | 3.1 N/mm² |
| Maximum temperature resulting in a TSS of 5 N/mm² | 80 °C |
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
- H335 May cause respiratory irritation.
- H351 Suspected of causing cancer.
- H373 May cause damage to organs through prolonged or repeated exposure.
- H373 May cause damage to organs through prolonged or repeated exposure by inhalation.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P260 Do not breathe mist or vapours.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves/protective clothing/eye protection/face protection.
- P304 + P340 + P312 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER/doctor if you feel unwell.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P308 + P313 IF exposed or concerned: Get medical advice/attention.
- P337 + P313 If eye irritation persists: Get medical advice/attention.
- P501 Dispose of contents/container at an approved waste disposal facility in accordance with local/regional/national/international regulations.
Araldite® 2030 50ml
Paste-like two-component epoxy adhesive
- High shear and peel strength
- Robust and durable
- Good resistance to dynamic loads
- Suitable for bonding a wide range of common materials
Araldite® 2030 is a fast-curing, high-viscosity, general-purpose two-component adhesive that cures at room temperature and offers high strength and toughness.
It is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics, and most other common materials.
This is a versatile adhesive suitable for most craft and industrial applications.
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
| 2K epoxy adhesive | |
|---|---|
| Viscosity | 30–45 Pa·s |
| Working time (23°C) | 100 minutes |
| Handling strength (1 MPa) at 23°C | 7 hours |
| Strength (10 MPa) at 23°C | 10 hours |
| 50% strength (60°C) | 45 minutes |
| Tensile shear strength (23°C) on ABS | 6 MPa |
| Tensile shear strength (23°C) on aluminum | 26 MPa |
| Peel strength (23°C) | 5 N/mm² |
| Typical Tg (softening temperature) | 45 °C |
| Maximum temperature resulting in TSS of 5 MPa | 90 °C |
Araldite® 2031-1 50ml
Black, paste-like two-component epoxy adhesive
- Thixotropic, non-sagging
- Tough-elastic adhesive
- Suitable for bonding plastics, composites and metals
- Good adhesion to polyamides
- Excellent chemical resistance
- Low shrinkage
Note: Araldite® 2021-1 is not suitable for bonding copper, brass or copper alloys.
Araldite® 2031-1 is a two-component, paste-like adhesive that cures at room temperature and forms a durable bond. The thixotropic paste does not run at application thicknesses of up to 10 mm and is particularly suitable for SMC and GRP (GFK) bonding.
| 2K EP epoxy adhesive with a mixing ratio of 1:1 | |
|---|---|
| Color (mixed) | black |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 60 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 360 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 19 N/mm² |
| Young’s modulus at 23°C | 1000 N/mm² |
| Elongation at break at 23°C | 5 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 4 N/mm² |
| Glass transition temperature, cure 16 h / 40°C | 65 °C |
| Maximum temperature resulting in TSS of 5 N/mm² | 105 °C |
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information
(status 06/2018 & 07/2018)
- Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H304 May be fatal if swallowed and enters airways.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapors.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Wash skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P391 Collect spillage.
Araldite® 2047-1 50ml
Methacrylate-based adhesive for lightly pretreated surfaces
- Gap-filling
- Only minimal surface pre-treatment required
- Good adhesion on substrates that are otherwise difficult to bond
- High resistance across a broad temperature range
- Good adhesion even at low temperatures
Note: Can only be processed with the MIXPAC DS 51 application gun (item number: EPI-20017)!
Araldite® 2047-1 is a cold-curing, two-component methacrylate adhesive for bonding metals and plastics. Depending on the application method, Araldite® 2047-1 fills gaps of approximately 5 mm. For many bonds, no elaborate surface preparation is required, or it can be reduced to a minimum. The adhesive can be processed at temperatures up to 40°C; at higher temperatures, the curing time is shortened.
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | brown |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 5 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 5 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 12 N/mm² |
| Young’s modulus at 23°C | 850 N/mm² |
| Elongation at break at 23°C | 32 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 3 N/mm² |
| Maximum temperature resulting in TSS of 5 N/mm² | 95 °C |
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information
(status 05/2015 & 10/2015)
- Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H241 Heating may cause a fire or explosion.
- H242 Heating may cause a fire.
- H301 Toxic if swallowed.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H351 Suspected of causing cancer.
- H400 Very toxic to aquatic life.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P220 Keep away from clothing and other combustible materials.
- P233 Keep container tightly closed.
- P234 Keep only in original packaging.
- P235 Keep cool.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P362 + P364 Take off contaminated clothing and wash it before reuse.
- P370 + P378 In case of fire: Use dry sand, extinguishing powder or alcohol-resistant foam to extinguish.
- P410 Protect from sunlight.
- P420 Store away from other materials.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2047-1 480ml dual cartridge with static mixing nozzle
Methacrylate-based adhesive for lightly pretreated surfaces
- Gap-filling
- Only minimal surface pre-treatment required
- Good adhesion on substrates that are otherwise difficult to bond
- High resistance across a broad temperature range
- Good adhesion even at low temperatures
Araldite® 2047-1 is a cold-curing, two-component methacrylate adhesive for bonding metals and plastics. Depending on the application method, Araldite® 2047-1 fills gaps of approximately 5 mm. For many bonds, no elaborate surface preparation is required, or it can be reduced to a minimum. The adhesive can be processed at temperatures up to 40°C; at higher temperatures, the curing time is shortened.
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | brown |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 5 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 5 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 12 N/mm² |
| Young’s modulus at 23°C | 850 N/mm² |
| Elongation at break at 23°C | 32 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 3 N/mm² |
| Maximum temperature resulting in TSS of 5 N/mm² | 95 °C |
Buy application gun / dual-cartridge gun – MIXPAC DM 400
- Packaging: 480ml dual cartridge with static mixing nozzle
- Net weight: 0.48kg
Product safety information
(status 05/2015 & 10/2015)
- Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapour.
- H241 Heating may cause a fire or explosion.
- H242 Heating may cause a fire.
- H301 Toxic if swallowed.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H331 Toxic if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H351 Suspected of causing cancer.
- H400 Very toxic to aquatic life.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P220 Keep away from clothing and other combustible materials.
- P233 Keep container tightly closed.
- P234 Keep only in original packaging.
- P235 Keep cool.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P362 + P364 Take off contaminated clothing and wash it before reuse.
- P370 + P378 In case of fire: Use dry sand, extinguishing powder or alcohol-resistant foam to extinguish.
- P410 Protect from sunlight.
- P420 Store away from other materials.
- P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Araldite® 2048 50ml
Toughened, flexible two-component methacrylate adhesive
- Fast curing
- Very well suited for a wide range of metals and plastics
- Tolerant of less-than-ideal surface preparation
- Gap-filling properties up to 8 mm
- Tough, flexible bond lines – well suited for dynamic loads
Araldite® 2048 is a two-component methacrylate adhesive that cures at room temperature. It is a fast-curing adhesive that is very well suited for bonding and repairing metals, composites and thermoplastics.
Note: Can only be used with the MIXPAC DS 51 application gun (item number: EPI 20024)!
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | brown |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 5 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 5 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 12 N/mm² |
| Young’s modulus at 23°C | 850 N/mm² |
| Elongation at break at 23°C | 32 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 3 N/mm² |
| Maximum temperature resulting in TSS of 5 N/mm² | 95 °C |
Go to the product: MIXPAC DS 51 application gun
Araldite® 2048 480ml
Toughened, flexible two-component methacrylate adhesive
- Fast curing
- Very well suited for a wide range of metals and plastics
- Tolerant of less-than-ideal surface preparation
- Gap-filling properties up to 8 mm
- Tough, flexible bond lines – well suited for dynamic loads
Araldite® 2048 is a two-component methacrylate adhesive that cures at room temperature. It is a fast-curing adhesive that is very well suited for bonding and repairing metals, composites and thermoplastics.
Note: Can only be used with the MIXPAC DMA 4001 application gun (item number: EPI 20025)!
- Packaging: 480ml dual cartridge with static mixing nozzle
- Net weight: 0.48kg
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | red |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 10 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 15 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 24 N/mm² |
| Young’s modulus at 23°C | 360 N/mm² |
| Elongation at break at 23°C | 91 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 5.4 N/mm² |
| Maximum temperature resulting in TSS of 5 N/mm² | 97 °C |
Go to the product: MIXPAC DS 51 application gun
Araldite® 2052-1 50ml dual cartridge with static mixing nozzle
Methacrylate-based adhesive with good temperature resistance
- Fast curing
- Resistant to very high temperatures
- Excellent resistance to chemicals
- Thixotropic paste
- Good adhesion even without special surface pretreatment
Araldite® 2052-1 provides excellent strength on metals as well as on rigid plastics, even without special pretreatment of the parts to be bonded. Normal rolling oil and drawing oil residues are relatively compatible with Araldite® 2052-1. The adhesive offers good thermal stability and good gap-filling properties for bond lines with a width of at least 5 mm.
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | brown |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 5 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 5 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 12 N/mm² |
| Young’s modulus at 23°C | 850 N/mm² |
| Elongation at break at 23°C | 32 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 3 N/mm² |
| Maximum temperature resulting in TSS of 5 N/mm² | 95 °C |
- Packaging: 50ml dual cartridge with static mixing nozzle
- Net weight: 0.05kg
Product safety information
(status 09/2018 & 01/2020)
- Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapor.
- H241 Heating may cause a fire or explosion.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P261 Avoid breathing dust / smoke / gas / mist / vapors / spray.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
- P337 + P313 If eye irritation persists: Get medical advice/attention.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P391 Collect spillage.
Araldite® 2052-1 480ml
Methacrylate-based adhesive with good temperature resistance
- Fast curing
- Resistant to very high temperatures
- Excellent resistance to chemicals
- Thixotropic paste
- Good adhesion even without special pretreatment
Araldite® 2052-1 provides excellent strength on metals as well as on rigid plastics, even without special pretreatment of the parts to be bonded. Normal rolling oil and drawing oil residues are relatively compatible with Araldite® 2052-1. The adhesive offers good thermal stability and good gap-filling properties for bond lines with a width of at least 5 mm.
| 2K MMA methacrylate adhesive with a mixing ratio of 10:1 | |
|---|---|
| Color (mixed) | light red |
| Viscosity | thixotropic (paste-like) |
| Working time for 100 g at 23°C | 15 minutes |
| Handling strength at 23°C for TSS 1 N/mm² | 20 minutes |
| Tensile shear strength (TSS) on aluminum at 23°C | 25 N/mm² |
| Young’s modulus at 23°C | 1550 N/mm² |
| Elongation at break at 23°C | 5 % |
| Roll peel test (ISO 4587), cure 16 h / 40°C | 3 N/mm² |
| Glass transition temperature, cure 16 h / 40°C | 120 °C |
| Maximum temperature resulting in TSS of 5 N/mm² | 140 °C |
- Packaging: 500ml dual cartridge with static mixing nozzle
- Net weight: 0.48kg
Product safety information
(status 09/2018 & 01/2020)
- Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H225 Highly flammable liquid and vapor.
- H241 Heating may cause a fire or explosion.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H400 Very toxic to aquatic life.
- H410 Very toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P261 Avoid breathing dust / smoke / gas / mist / vapors / spray.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER / doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
- P337 + P313 If eye irritation persists: Get medical advice/attention.
- P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
- P391 Collect spillage.
Araldite® AW 134
AW 134 is a component of a two-component epoxy adhesive.
- cures at room temperature
- solvent-free
- good heat resistance
Araldite® AW 134 with Hardener HY 991 is a two-component, room-temperature curing, viscous liquid adhesive with high strength and toughness. It is suitable for bonding a wide range of metals, ceramics and many other commonly used substrates.
| AW 134 | |
|---|---|
| Color | white to beige paste |
| Viscosity (Pa·s) | 20 – 40 |
| Specific gravity | 1.2 – 1.3 |
Safety information for Araldite® AW 134 (status 09/2018)
- Signal word: Warning
GHS Safety Statements / H Statements
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
Additional labeling
- EUH205 Contains epoxy-containing compounds. May cause an allergic reaction.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapors.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
- P391 Collect spillage.
Araldite® AW 2101 / HW 2951 – Cans
Paste-like, fast-curing two-component epoxy adhesive
- fast curing
- slightly thixotropic
- gap-filling
- excellent resistance to gasoline and oil
Araldite® AW 2101 / Hardener HW 2951 is a paste-like, general-purpose, two-component adhesive for industrial applications that cures quickly at room temperature.
The adhesive offers good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials.
| Properties | Araldite® AW 2101 | Hardener HW 2951 | Mixed adhesive |
|---|---|---|---|
| Color (visual) | white paste | gray paste | gray paste |
| Density | approx. 1.65 | approx. 1.9 | approx. 1.8 |
| Viscosity at 25°C (Pa·s) | 35 – 45 | 25 – 40 | thixotropic |
| Lap shear strength at 25°C | – | – | > 14 MPa |
| Pot life (100 g at 25°C) | – | – | 4 – 8 minutes |
| Safety information for the components | Araldite® AW 2101 (status 01/2018) | Hardener HW 2951 (status 01/2019) |
|---|---|---|
| Signal word | Danger | Danger |
| Hazard pictograms |    | |
| GHS safety information / H statements |
|
|
| GHS safety information / P statements |
|
|
Araldite® AW 2101 / HW 2951 – Cartridges
Paste-like, fast-curing two-component epoxy adhesive
- fast curing
- slightly thixotropic
- gap-filling
- excellent resistance to gasoline and oil
Araldite® AW 2101 / Hardener HW 2951 is a paste-like, general-purpose, two-component adhesive for industrial applications that cures quickly at room temperature.
The adhesive offers good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials.
| Properties | Araldite® AW 2101 | Hardener HW 2951 | Mixed adhesive |
|---|---|---|---|
| Color (visual) | white paste | gray paste | gray paste |
| Density | approx. 1.65 | approx. 1.9 | approx. 1.8 |
| Viscosity at 25°C (Pa·s) | 35 – 45 | 25 – 40 | thixotropic |
| Lap shear strength at 25°C | – | – | > 14 MPa |
| Pot life (100 g at 25°C) | – | – | 4 – 8 minutes |
Product safety information
(status 01/2018 & 01/2019)
- Signal word: Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing mist or vapors.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
- P304 + P340 + P310 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER/doctor.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor.
- P391 Collect spillage.
- P501 Dispose of contents/container in accordance with local/regional/national/international regulations.
Araldite® AY 103-1
Product safety information (status 09/2018)
Signal word: Danger
GHS Safety Statements / H Statements
- H304 May be fatal if swallowed and enters airways.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H319 Causes serious eye irritation.
- H410 Very toxic to aquatic life with long lasting effects.
- H411 Toxic to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust / smoke / gas / mist / vapors / spray.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P301 + P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor.
- P331 Do NOT induce vomiting.
- P391 Collect spillage.
Araldite® Rapid
- Fast curing
- All-purpose adhesive
- Low shrinkage
- For bonding a wide variety of materials
- Tough and elastic
Araldite® Rapid is a fast-curing, general-purpose two-component adhesive. The product is characterized by good contact adhesion and toughness and is suitable for bonding a wide range of metals, ceramics, glass, rubber, rigid plastics and most commonly used materials. It is a versatile adhesive suitable for both craft applications and most industrial uses.
| Properties | Araldite® Rapid Resin | Araldite® Rapid Hardener | Araldite® Rapid Mixture |
|---|---|---|---|
| Color (visual) | opaque | light yellow | light yellow |
| Density | 1.16–1.18 | 1.15–1.18 | approx. 1.18 |
| Viscosity at 25°C (Pa·s) | 30–75 | 20–40 | approx. 25–50 |
| Pot life (100 g at 25°C) | – | – | 5 – 8 minutes |
KS 11 Paste-like 2K EP Structural Adhesive
is a paste-like, general-purpose two-component adhesive that cures at room temperature. The paste is characterized by good contact adhesion and toughness and is suitable for bonding many materials such as metals, ceramics, glass, rubber and rigid plastics.
- All-purpose adhesive
- long service life
- low shrinkage
- good resistance to dynamic loads
- for bonding a wide variety of commonly used materials
- temperature resistance up to 80 °C
Product safety information (status 12/2016)
Signal word: Danger + Warning
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
Additional information
- EUH205 Contains epoxy constituents. May produce an allergic reaction.
GHS Safety Statements / P Statements
- P260 Do not breathe dust / smoke / gas / mist / vapors / spray.
- P261 Avoid breathing dust / smoke / gas / mist / vapors / spray.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water / shower.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
- P310 Immediately call a POISON CENTER / doctor.
- P362+P313 If skin irritation occurs: Get medical advice / attention.
- P501 Dispose of contents / container in accordance with local / regional / national / international regulations.
KS 12 Paste-like 2K EP Structural Adhesive
is a fast-curing, high-viscosity, general-purpose two-component epoxy adhesive that cures at room temperature. The thixotropic paste is characterized by good contact adhesion and toughness and is suitable for bonding many materials such as ceramics, glass, rubber and rigid plastics.
- All-purpose adhesive
- fast curing
- tough and elastic
- low shrinkage
- for bonding a wide variety of materials
- temperature resistant up to 60 °C
Product safety information (status 07/2016 & 05/2018)
Signal word: Warning
GHS Safety Statements / H Statements
- H226 Flammable liquid and vapor.
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H332 Harmful if inhaled.
- H336 May cause drowsiness or dizziness.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P261 Avoid breathing dust / smoke / gas / mist / vapors / spray.
- P264 Wash skin thoroughly after handling.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P362 + P364 Take off contaminated clothing and wash it before reuse.
- P391 Collect spillage.
- P501 Dispose of contents / container in accordance with all local / regional / national / international regulations.
KS 13 Paste-like 2K EP Structural Adhesive
is a paste-like two-component adhesive that cures at room temperature. It stands out for its good contact adhesion and strength as well as its excellent resistance to environmental influences and chemicals.
Application area
Particularly suitable for bonding metals, as well as ceramics, glass, rubber, rigid plastics and most commonly used materials.
Properties
- gap-filling up to 5 mm
- non-sag
- thixotropic paste
- medium working time approx. 70 min
- handling strength approx. 4 hours
- final strength after approx. 10 hours
- heat deflection resistance: -40 °C to 65 °C
- color: gray
Attention: This product currently contains Bisphenol A (EC No. 201-245-8), which is registered under REACH (European chemicals regulation). This means that, by law, this product may currently not be supplied to private end consumers. Only commercial customers or customers with appropriate qualifications for processing this adhesive are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will be made, as we would otherwise be liable to prosecution. Your order will then be canceled and any amounts already paid will be refunded.
Thank you for your understanding!
Product safety information (status 09/2017 & 05/2016)
Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H330 Fatal if inhaled.
- H332 Harmful if inhaled.
- H335 May cause respiratory irritation.
- H360F May damage fertility.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P201 Obtain special instructions before use.
- P261 Avoid breathing mist or vapors.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor.
- P308 + P313 IF exposed or concerned: Get medical advice / attention.
- P405 Store locked up.
- P501 Dispose of contents / container in accordance with local / regional / national / international regulations.
Additional labeling
- Contains epoxy-containing compounds. Follow the manufacturer’s instructions.
KS 14 Paste-like 2K EP Structural Adhesive
Description
KS 14 is a paste-like two-component adhesive that cures at room temperature. The paste stands out for its good contact adhesion, strength, and its excellent resistance to environmental influences and chemicals.
Application area
Especially suitable for professional electronic communication and aerospace applications, as well as for bonding metal, electronic components and GRP (glass fiber reinforced plastic) components.
Properties
- low shrinkage
- gap-filling up to 5 mm
- non-sag
- paste-like consistency
- medium working time approx. 60 min
- handling strength approx. 3.5 hours
- final strength after approx. 5 hours
- heat deflection resistance: -40 °C to 120 °C
- color: gray
Product safety information (status 06/2019)
Signal word: Warning + Danger
GHS Safety Statements / H Statements
- H302 Harmful if swallowed.
- H311 Toxic in contact with skin.
- H312 Harmful in contact with skin.
- H314 Causes severe skin burns and eye damage.
- H315 Causes skin irritation.
- H317 May cause an allergic skin reaction.
- H318 Causes serious eye damage.
- H319 Causes serious eye irritation.
- H361fd Suspected of damaging fertility. Suspected of damaging the unborn child.
- H372 Causes damage to organs (respiratory tract) through prolonged or repeated exposure (inhalation, skin contact).
- H373 May cause damage to organs through prolonged or repeated exposure.
- H411 Toxic to aquatic life with long lasting effects.
- H412 Harmful to aquatic life with long lasting effects.
GHS Safety Statements / P Statements
- P260 Do not breathe dust / fume / gas / mist / vapors / spray.
- P261 Avoid breathing dust / fume / gas / mist / vapors / spray.
- P273 Avoid release to the environment.
- P280 Wear protective gloves / protective clothing / eye protection / face protection.
- P302 + P352 IF ON SKIN: Wash with plenty of water.
- P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water / shower.
- P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P310 Immediately call a POISON CENTER / doctor.
- P333 + P313 If skin irritation or rash occurs: Get medical advice / attention.
- P501 Dispose of contents / container to a suitable recycling or disposal facility.
Additional labeling
- Contains epoxy-containing compounds. Follow the manufacturer’s instructions.
KS 15 Paste-like 2K EP Structural Adhesive
KS 15 is a paste-like, room-temperature curing, two-component epoxy-based adhesive that produces an elastic bond. The thixotropic paste is non-sag up to an application thickness of 10 mm and is particularly suitable for SMC and GRP (GFRP) bonding.
- tough and elastic paste
- low shrinkage
- ideal for bonding GRP/GFRP, SMC and dissimilar substrates
- gap-filling, non-sag up to 10 mm application thickness
- high lap shear and peel strength
PRODUCT INFORMATION “KS 15 PASTE EPOXY SYSTEM 50 ML CARTRIDGE”
Application area
Especially suitable for bonding metals, as well as ceramics, glass, rubber, rigid plastics and most commonly used materials.
Description
KS 15 is a paste-like, room-temperature curing 2K epoxy-based adhesive that creates an impact-resistant (tough) bond.
Fields of application
For bonding GRP/GFRP, SMC and a wide variety of substrates.
Properties
- low shrinkage
- gap-filling up to 10 mm
- high lap shear and peel strength
- tough-elastic paste
- medium working time approx. 40 min
- handling strength approx. 4 hours
- final strength after approx. 10 hours
- heat deflection resistance: -40 °C to 80 °C
- color: beige
IMPORTANT! Only commercial customers or customers with the appropriate qualification are allowed to purchase this product. If you place an order, our customer service will contact you after receipt of your order to verify the relevant commercial requirements. If you do not meet these requirements, no delivery will be made, as we would otherwise be committing an offense. Your order will then be cancelled and any amounts already paid will be refunded.
Thank you for your understanding!
KS 21 Beige (transparent) or Black 2K MMA Adhesive
Description
KS 21 is a high-performance, two-component structural adhesive based on methacrylic ester (MMA) with a 1:1 mixing ratio, designed for bonding high-quality components without surface pretreatment.
Application area
For bonding metal, thermoplastics, composites, glass, ceramics and ABS.
Properties
- gap-filling
- high mechanical strength
- working time: approx. 3 min
- good ageing resistance
- B-CARTRIDGE SYSTEM
- color: beige (transparent) or black
KS 22 2K MMA Adhesive
Description
is a two-component high-performance adhesive based on methacrylic ester for structural bonding of high-quality fiber-reinforced composite components, usually without surface pretreatment.
Application area
For bonding metal, thermoplastics, composite materials, glass, ceramics and ABS.
Properties
- gap-filling
- high mechanical strength
- working time: approx. 8–10 min
- good ageing resistance
- B-CARTRIDGE SYSTEM
- color: beige
KS 29 2K PUR Adhesive
PRODUCT INFORMATION “KS 29 PU SYSTEM 50 ML CARTRIDGE”
KS 29 is a two-component high-performance adhesive based on polyurethane for rapid fixing. On most substrates, no surface pretreatment is required. Fast curing as well as very good impact, vibration and sound damping characterize this adhesive.
Application area
For bonding thermoplastic components, composite parts and body components.
Properties
- gap-filling: up to 6.0 mm
- flexible (Shore A 90)
- processing time: approx. 3–5 min
- temperature resistance: from -40 °C to +100 °C
- color: black
KS 49 2K EP Structural Adhesive
PRODUCT INFORMATION “KS 49 EPOXY ADHESIVE 200 ML CARTRIDGE”
KS 49 is a two-component high-performance adhesive based on epoxy resin for structural bonding of different materials such as metal, glass, plastics, composite materials, ABS, rigid PVC and PMMA!
Application area
For bonding high-quality fiber-reinforced composite components, tools for RTM/RIM, model making, vehicle, ship and boat construction, electrical and switchgear engineering and much more.
Properties
- tough-elastic
- increased heat resistance
- high strength
- color: black
1 Min PU flex 50 ml Cartridge
Description
1 Min PU flex is a 2K double cartridge based on polyurethane for structural and cosmetic repair of plastic parts (flexible materials). Due to the double cartridge and the forced mixing via a mixing tube, the components are automatically mixed and dosed easily and cleanly. Curing takes place immediately after extrusion through a chemical reaction. The viscous compound is suitable for repairing, filling, sealing and bonding.
Application area
Model making, prototype construction, automotive industry, body and vehicle construction, apparatus, container and mold construction. Joining prototypes, repairing broken plastic parts, brackets, trims and housings. For filling holes, cracks and joints.
Properties
- fast curing
- working time 1 min
- flexible (Shore A92)
- high-strength, durable bonds
- weather- and ageing-resistant
- oil-, fuel- and water-resistant
- solvent-, acid- and alkali-resistant
- shrink-free
- color: black
1 Min PU rigid 50 ml Cartridge
Description
1 Min PU rigid is a 2K double cartridge based on polyurethane for the structural and cosmetic repair of plastic parts (rigid materials). Due to the double cartridge and forced mixing via a mixing nozzle, the components are automatically mixed and dispensed easily and cleanly. Curing takes place immediately after extrusion through a chemical reaction. The viscous compound is suitable for repairing, filling, sealing and bonding.
Application area
Model making, prototype construction, automotive industry, body and vehicle construction, apparatus, container and mold construction. Joining prototypes, repairing broken plastic parts, brackets, trims and housings. For filling holes, cracks and joints.
Properties
- fast curing
- working time 1 min
- rigid (Shore 78D)
- high-strength, durable bonds
- weather- and ageing-resistant
- solvent-, acid- and alkali-resistant
- shrink-free
- color: black
5 Min PU flex 50 ml Cartridge
Description
5 Min PU flex is a 2K double cartridge based on polyurethane for the structural and cosmetic repair of plastic parts (flexible materials). Due to the double cartridge and forced mixing via a mixing tube, the components are automatically mixed and dispensed easily and cleanly. Curing takes place immediately after extrusion through a chemical reaction. The viscous compound is suitable for repairing, filling, sealing and bonding.
Application area
Model making, prototype construction, automotive industry, body and vehicle construction, apparatus, container and mold construction. Joining prototypes, repairing broken plastic parts, brackets, trims and housings. For filling holes, cracks and joints.
Properties
- fast curing
- working time 5 min
- flexible (Shore 60D)
- high-strength, durable bonds
- weather- and ageing-resistant
- oil-, fuel- and water-resistant
- solvent-, acid- and alkali-resistant
- shrink-free
- color: black
5 Min PU rigid 50 ml cartridge
Description
5 Min PU rigid is a 2K double cartridge based on polyurethane for the structural and cosmetic repair of plastic parts (rigid materials). Due to the double cartridge and forced mixing via a mixing tube, the components are automatically mixed and dispensed easily and cleanly. Curing takes place immediately after extrusion through a chemical reaction. The viscous compound is suitable for repairing, filling, sealing and bonding.
Application area
Model making, prototype construction, automotive industry, body and vehicle construction, apparatus, container and mold construction. Joining prototypes, repairing broken plastic parts, brackets, trims and housings. For filling holes, cracks and joints.
Properties
- fast curing
- working time 5 min.
- rigid (Shore78D)
- high-strength, durable bonds
- weather- and ageing-resistant
- oil-, fuel- and water-resistant
- solvent-, acid- and alkali-resistant
- shrink-free
- color: black